The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

jme (4)
  • >> jme (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    jme
    
     - JMicron Gigabit/Fast Ethernet driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device miibus device jme

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_jme_load="YES"
    
     

    DESCRIPTION

    The device driver provides support for JMicron JMC250 PCI Express Gigabit Ethernet controllers and JMicron JMC260 PCI Express Fast Ethernet controllers.

    All LOMs supported by the driver have TCP/UDP/IP checksum offload for both transmit and receive, TCP segmentation offload (TSO), hardware VLAN tag stripping/insertion features, Wake On Lan (WOL) and an interrupt coalescing/moderation mechanism as well as a 64-bit multicast hash filter.

    The JMC250 also supports Jumbo Frames (up to 9216 bytes), which can be configured via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames.

    The driver supports the following media types:

    autoselect
    Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf5.
    10baseT/UTP
    Set 10Mbps operation.
    100baseTX
    Set 100Mbps (Fast Ethernet) operation.
    1000baseTX
    Set 1000baseTX operation over twisted pair.

    The driver supports the following media options:

    full-duplex
    Force full duplex operation.
    half-duplex
    Force half duplex operation.

    For more information on configuring this device, see ifconfig(8).  

    LOADER TUNABLES

    Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf5.

    hw.jme.msi_disable
    This tunable disables MSI support on the Ethernet hardware. The default value is 0.
    hw.jme.msix_disable
    This tunable disables MSI-X support on the Ethernet hardware. The default value is 0.

     

    SYSCTL VARIABLES

    The following variables are available as both sysctl(8) variables and loader(8) tunables:

    dev.jme.%d.tx_coal_to
    Maximum amount of time to delay for Tx completion interrupt in units of 1us. The accepted range is 1 to 65535, the default is 100 (100us).
    dev.jme.%d.tx_coal_pkt
    Maximum number of packets to fire Tx completion interrupt. The accepted range is 1 to 255, the default is 8.
    dev.jme.%d.rx_coal_to
    Maximum amount of time to delay for Rx completion interrupt in units of 1us. The accepted range is 1 to 65535, the default is 100 (100us).
    dev.jme.%d.rx_coal_pkt
    Maximum number of packets to fire Rx completion interrupt. The accepted range is 1 to 255, the default is 2.
    dev.jme.%d.process_limit
    Maximum amount of Rx events to be processed in the event loop before rescheduling a taskqueue. The accepted range is 10 to 255, the default value is 128 events. The interface does not need to be brought down and up again before a change takes effect.

     

    SEE ALSO

    altq(4), arp(4), miibus(4), netintro(4), ng_ether4, vlan(4), ifconfig(8)  

    HISTORY

    The driver was written by An Pyun YongHyeon Aq yongari@FreeBSD.org . It first appeared in Fx 7.1 .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    LOADER TUNABLES
    SYSCTL VARIABLES
    SEE ALSO
    HISTORY


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру